Litigation support · Guide

Bates numbering best practices

Bates numbering works when the scheme is fixed before the first page is stamped: a party prefix, enough leading zeros, one placement, and an index that maps every file to its number range.

Muhammad DanishIndependent consultant · Updated 15 November 2026
On this page
  1. What Bates numbering is for
  2. The four parts of a scheme
  3. Before stamping: the production index
  4. The stamping process
  5. Common errors
  6. Bates numbers and exhibit stamps
  7. Confidentiality legends
  8. Redactions
  9. A production checklist

Bates numbering looks like a formatting task until a production is challenged. Then it becomes a records question: what was produced, on which page, and can the firm prove it? The number is the thread that answers all three.

The conventions below are the ones that hold up in practice. None of them are universal rules — courts, agreements and opposing counsel can each impose requirements — but they are a sensible default for a small litigation team.

What Bates numbering is for

A Bates number gives every page in a production a unique, sequential identifier. The number does three jobs:

  • Identification — a page can be cited unambiguously in a letter, brief or deposition.
  • Ordering — the sequence shows where a page sits in the production.
  • Proof — the number range shows what was produced and what was not.

A production without Bates numbers can still be produced, but it cannot be cited with the same precision, and supplementing it later is harder because there is no stable reference.

The four parts of a scheme

1. Prefix. A short identifier for the producing party or firm: `SMITH`, `DEF`, `ABC`. Keep it consistent across the matter. If there are multiple producing parties, each gets its own prefix.

2. Number. Sequential, starting from a defined point. Starting at 1 is fine for a small production; larger matters may reserve blocks for different categories.

3. Padding. Leading zeros to a fixed width: `000001`. Six digits covers 999,999 pages. Choose the width before stamping and do not change it mid-production.

4. Placement. One position for the entire production, usually bottom right or bottom centre. It must be legible, must not cover content, and must survive black-and-white printing.

A consistent scheme looks like `SMITH000001`, `SMITH000002`, and so on. The exact format matters less than the consistency.

Before stamping: the production index

Build the index first, not after. A simple table:

FileBates startBates endPagesCategoryConfidential?
2024-03-12 - Invoice.pdfSMITH000001SMITH0000033FinancialNo
2024-04-02 - Email chain.pdfSMITH000004SMITH0000096CorrespondenceYes

The index does four things: it proves the page count, it produces the range for the transmittal letter, it supports a later supplement, and it lets someone answer "where is that document?" without opening every file.

The stamping process

  1. Freeze the document set. No additions after numbering starts, or the sequence will have gaps.
  2. Sort the files in the order they will be produced. Numbering follows the production order, not the folder order.
  3. Set the scheme — prefix, start number, padding, position, font size.
  4. Stamp a test batch of two or three files and inspect the output at 100% zoom.
  5. Stamp the full batch.
  6. Verify the index — page counts, start and end numbers, no duplicates, no gaps.
  7. Record the production in the production log.

Step 6 is the quality control step. A duplicate number or a gap is much easier to fix before the production is served than after.

Common errors

Changing the prefix mid-production. Two numbering systems in one case, and no clean way to cite across them.

Inconsistent padding. `SMITH1` and `SMITH000002` in the same production look like two schemes and sort incorrectly.

Stamping over content. A number placed too close to text or a signature can obscure the page. Test the position on the widest and narrowest pages.

Stamping only the first page of a multi-page file. Every page needs a number, including cover sheets and exhibits.

Renumbering after production. If a page was produced with a number, that number should stay with it. Corrections are made by supplementing, not by renumbering the original.

No index. The production exists, but nobody can map a file to its number range without opening the PDFs.

Bates numbers and exhibit stamps

Bates numbers identify pages in a production. Exhibit stamps identify exhibits in a hearing or trial. They are different jobs:

  • Bates — sequential across the whole production, used for discovery and record citations.
  • Exhibit — a label per exhibit (`Plaintiff's Exhibit 12`), often with a separate exhibit list.

A document can carry both, and often does: a Bates number from the production and an exhibit sticker added later for trial. Do not replace one with the other, and record both in the index when both exist.

Confidentiality legends

A confidentiality legend is separate from the Bates number. If a document is designated confidential, the legend should be applied consistently to every page in the category, and the designation should be recorded in the production log.

Do not rely on the stamp alone to prove a designation. The production log and the transmittal letter are the record; the legend is the visible notice.

Redactions

If a document is produced with redactions, the Bates number should still appear on the page, and the redaction should be recorded in a redaction log with the basis. A redacted page without a number is difficult to cite and difficult to supplement.

The redaction itself must be burned in, not a black box over selectable text. That is a separate technical issue, but it is part of the same production discipline.

A production checklist

  • Document set frozen and sorted
  • Scheme agreed: prefix, start, padding, placement
  • Test batch inspected
  • Full batch stamped
  • Index built and verified: no duplicates, no gaps
  • Page counts match the index
  • Confidentiality legends applied where required
  • Redactions logged
  • Production log updated with date, recipient and Bates range
  • Copy of the produced files retained
  • Transmittal letter references the correct range

That checklist is short enough to run on every production and specific enough to catch the errors that matter.

Frequently asked questions

What is Bates numbering?

The practice of assigning a unique, sequential identifier to every page of a document production so a page can be cited and located without ambiguity. The number usually includes a party or firm prefix.

How many digits should a Bates number have?

Enough digits to cover the whole production without rolling over. Six is common for small matters; larger productions use seven or eight. Fix the width before stamping — changing it mid-production creates inconsistent citations.

Where should the Bates number appear?

Pick one position and keep it for the entire production — usually bottom right or bottom centre. The number must not obscure content, and it must be legible when printed in black and white.

Should confidential documents be stamped differently?

A confidentiality legend is separate from the Bates number. Apply it consistently to every page in the category, and record the category in the production log rather than relying on the stamp alone.

Do I need to keep a Bates index?

Yes. The index maps each source file to its starting and ending Bates number, which is how you answer a question about what was produced and where it sits in the production.

LawFirmTools provides software tools only. Nothing here is legal advice, and LawFirmTools is not a lawyer or a law firm. This article is general information for legal professionals; it is not a substitute for professional judgment or for your state bar's rules.